The ADA10000 is a monolithic IC intended for use in applications requiring high linearity, such as Cellular Telephone Base Station Driver Amplifiers, CATV Fiber Receiver and Distribution Amplifiers, and CATV Drop mAmplifiers. Offered in both a modified 16 lead SOIC package and SOT-89 package, it is well suited for use in amplifiers where small size, reduced component count, and high reliability are important.

The 35PD300-TO, an InGaAs photodiode with a 300µm-diameter photosensitive region packaged in a TO- 46 header. This device is one of Telcom Devices' most versatile optoelectronic components, with applications in high sensitivity instrumentation, laser back-facet monitoring, and moderate-bit-rate telecomm and datacomm transmission. Planar semiconductor design and dielectric passivation provide superior noise performance. Reliability is assured by hermetic sea

The AWS5506 is a Single Pole Double Throw GaAs MMIC switch assembled in a SOT-6 plastic package. The AWS5506 is designed for analog and digital application that require for insertion loss, small size,and low cost. State selection is achieved with a complimentary positive voltage (requires positive bias Vs, and blocking caps) or negative voltage (no Vs or blocking caps required).

DESCRIPTIONThe ARA05050 is a GaAs IC designed to provide the functions in a CATV Set-Top Box or Cable Modem. It incorporates a digitally controlled precision step attenuator that is preceded by an ultra low noise the MCNS/DOCSIS requirements for harmonic Fop Box AS28 with Heat performance at a +58dBmV output level while requiring only a single polarity +5V supply. Both the input and the output are single-ended and matched to 75 Ohms. The precision attenuator provides up to 30 dB offered in a 28-

DescriptionFigure 2: Pinout (X - ray op View)BSTXVBATTVRAM234567CEXT8PINNAMEDESCRIPTIONPINNAMEDESCRIPTIONbefore the DC blocking72BS8resistor before the DCblocking capacitor to set the34VBATTConnection5VRAMP6CEXTBypass (VREG)3AW02/2009Sdamage. Functional operation is not implied under these conditions. Eof time may adversely affect reliability.ETable 2: AFigure 3: Eof each pin are recorded. The ratings on each pin degradation. BS TX VBATT VRAMP23456 CEXT78 PARAMETER MIN MAX UNITSVBATT) - +5.5 VRF

SPECIFICATIONS Parameters Test Conditions Minimum Typical Maximum Units CLASS 1 (155 Mb/s) Rise and Fall Time 100mA 2.3 ns Link Bandwidth (­3dB) 155 MHz Data Rate 270 Mbps Coupled Optical Power 100mA, 62.5µm Fiber 35 uw CLASS 2 (622 Mb/s) Rise and Fall Time 1 ns Link Bandwidth (­3dB) 350 MHz Data Rate 625 Mbps Coupled Optical Power 100mA, 62.5µm Fiber 15 uw RATINGS Peak Wavelength 100mA 1260 1300 1340 nm Forward Voltage 100mA 1.3 V Spectral Width (FWHM) 100mA 120 nm Storage T

The ARa1400 and the ARA1400I are GaAs Ics designed to provide the reverse path amplification and output level control functions in a CATV Set-Top Box or Cable Modem. Each incorporates a digitally controlled precisions step attenuator that is preceded by an ultra low noise amplifier stage, and followed by anultra-linear output driver amplifier. These devices are capable of meeting the MCNS/DOCSIS requirements for harmionic performance at a +60dBmV output level while trequiring only a single pol

The 13PD300-FC, an InGaAs photodiode with a 300mm-diameter photosensitive region packaged in a TO-46 header and aligned in an FC active device mount, is designed for applications in both moderate-bit-rate fiberoptic communications and high sensitivity measurement equipment. This device is one of the most versatile of the Telcom Devices™ family of optoelectronic components. Planar semiconductor design and dielectric passivation provide superior performance. Reliability is assured by hermeti

The ARA2002 is designed to provide the reverse path amplification and output level control functions in a CATV Set-Top Box or Cable Modem.it incorporates a digitally controlled precition step attenuator that is preceded by an ultra Low noice amplifier stage, and followed by an ultra-linear output driver amplifier.

The AWT6130 provides the additional output power margin RF designers need to overcome additional post-PA insertion loss in tri-mode handset designs supporting E911 (GPS enabled). The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-the-art reliability, temperature stability, and ruggedness. Selectable bias modes that optimize efficiency for different output power levels, and a shutdown mode with low leakage current, increase handset talk and standby time. The sel